Retractor HD Tonneau Cover
- Heavy Duty Retracting Design
- Quality Aluminum Construction
- Simple Clamp On Mounting Process
- Cannister is Compact & out of the Way
- Low Profile Looks Amazing and Improves Gas Mileage
- Self Adjusting Track
- Constant Tension Spring Provides Years of Use
- Enhances Security
- Works In All Weather Conditions
- Compatible With Other Accessories
- The Retractor HD Tonneau Cover is Made in the USA
- Made in the USA
The Retractor HD tonneau cover has all the features you want, then goes beyond your expectations and gives you even more! A sleek low profile design, rugged aluminum panels, a small space saving canister and simple mounting are just a few of the features that make this retracting truck bed cover so ridiculously awesome!
The Retractor HD tonno cover mounts almost exactly flush with your truck bed for a super low profile look that will grab the attention of everyone around. A black powder coated finish is UV resistant and will not fade, chip or crack under normal use. A marine grade felt lined underside softens any noise when sliding the retracting tonneau cover in or out. The side rail channels are self aligning and allows for intermittent stopping. The only maintenance needed is to occasionally oil the rails to keep the cover sliding smoothly.
Constructed of ½" aircraft grade aluminum this bed cover is tough as nails and can take a beating. This retractable tonneau cover also has a dual latching system with glass reinforced nylon keeping your bed secure. To fully protect your truck bed Realtruck.com recommends you also get a tailgate lock.
The Retractor HD tonneau cover features a small canister that is about 9" square giving you more use of your truck bed for hauling. An integrated drain tube attached to sumps under the canister keep the canister dry and preventing and mildew and ice buildups.
With all these key features and more you cannot go wrong with choosing the Retractor HD tonneau cover for your pickup truck today!
Order NotesThe cargo management, utili-track, or deck rail system options refer to the factory installed rail system designed to hold moveable cargo cleats along the inside of your truck bed. Please call us for further clarification.
View Available Part Numbers For This Product Line
Adding a Rretractor HD tonneau cover to your truck is fairly simple and straight forward. You should have no problem putting it on right at home in your garage. there is minor drilling required to mount the canister to the inside of your truck bed rail. For additional information, please see the installation instructions below or call us at 1-866-309-1907 or 701-253-5906.
|Retractor HD Tonneau Cover Installation Instructions|
1 Year Warranty
The Retractor HD tonneau cover has a warranty of 1 year against any defects in material or workmanship. This warranty is offered directly through the manufacturing facility at BAK Industries. BAK takes the quality of our product very seriously. That is why the highest quality of material available is utilized to go into these covers. Unlike most lifetime warranties that have loopholes big enough to drive a truck through, our comprehensive warranty covers virtually all components!
In order to activate the warranty on your bed cover, please complete the warranty registration within 2 weeks of receiving your cover to ensure full warranty coverage at Warranty Registration
Related Articles (13)
Product Reviews Summary
|Ease of Installation||3.8|
|Price / Value||3.8|
|15 Customer Reviews|
Part #: R15203 Posted on
|Installation went fine but when it came to operating the cover...not real user friendly. First, if the cover fully retracts into the cover holder, it is impossible to pull it back out. There should be a stopping mechanism preventing it from retracting all the way into the roll up cover housing. The other problem is that when you want to retract the cover, it doesn't retract smoothly. You have to push it a lot. But as a cover it looks nice.|
Part #: R15101 Posted on
|This cover is durable easy to use, keeps items in bed secure, however Only secure with a locking tailgate. There is a slight gap with factory tailgate cap. Need to either remove or replace with a full length cap and bed rail caps.|
|REPLACING AN OLD VYNAL ROLE UP AND FOUND THIS TO BE THE BEST DESIGN / COST EFFFECTIVE FOR ME. CLEAN DESIGN WITH NO PROTRUSIONS AND SIMPLE LOCK SYSTEM THAT CLEARS MY MONSTER 5TH WHEEL AIR RIDE HITCH. TOOK LONGER TO INSTALL, BUT I AM PICKI ABOUT MY TRUCK AND AM OLD AND WEAK NOW. I USED THIN PLASTIC SHIMMS AROUND THE SIDE RAILS TO EVEN OUT MY BED DESIGN AND KEEP THE RAILES FROM LEANING IN TO THE BED. WISH THIS HAD BEN AVALABLE TO ME IN '96, THEN I WOULD NOT HAVE HAD TO REPLACE IT. THIS TOP WILL LAST ME FOR THE REAST OF MY LIFE....|
|Honestly I'm satisfied at this point. Installation is not difficult but the latch system is not what is shown on your web ad[your ad shows a pin latch and this one has a cable pull] and the cannister cover wouldn't seal out anything less than 1/2", the debris brush doesn't come close I can slide my hand under it and there's nothing that can be done without modification. The cover looks great there are some flaws in the finish here and there but i'm pretty picky|
|Ease of installation was overstated, but only a little. Operation was difficult due to binding. After several iterations at lubrication and adjustment the cover now seems to be appropriately aligned and works very well. Stake pockets are left open and available for use. Tracked MPG for 1200 miles before and 700 miles (so far) after - gained 1.2 mpg from before to after. Overall: Looks like it will do good, but be prepared to tedious installation.|
|I like the cover, but it was a real bear to install. The instructions were incomplete or insufficiently detailed enough to make a proper installation. I had to call the manufacturer to get further instructions. The "man" with the knowledge was out sick, but they would have him call me. They didn't! I had to call twice more before I finally reached him. He said I need shims on my rails. Nothing in the instructions about shims. And there wasn't enough shims provided. The clamps did not want to stay in position while they were tightened either. A 25 minute installation took more than 4 hours. I would, probably, buy another one from RealTruck. The price was good and the service was good. The manufacture just needs to be more clear on their instructions.|
|Every thing is okay about the top i have. It was easy to put together.If I has to do over Realtruck would be the one. I will be tell all my friends about my service. Thank you.|
|Works as advertized, really happy with the way it securly covers tools & equipment in the bed of my truck. Install is pretty simple & straight forward and would not have taken that long, but I had to cut away a section of my bedliner in the front of my truck since the bedliner was curved too much and about 5" from the wall of the truck. Price is great & was $160 less than the rollbak G2 which this actually is. only installed one week ago so can't comment on long term reliability.|