Truxedo TruxSeal Tailgate Seal Gasket Kit

TruXedo TruxSeal Tailgate Seal Warranty

TruXedo® Lo Pro   :   Lifetime Warranty Hassle free lifetime warranty covers everything, even the fabric (Applies to original owner). Shur-Co.® warrants that all new, unused products are free from defects in material and workmanship. This warranty is effective if the product is properly installed and used for the purpose intended for the life of the product. It applies to the original buyer only. Shur-Co.®'s obligation under this warranty is limited to repairing, or at its option, replacing any part that is returned, transportation prepaid, to Shur-Co.®, Yankton, South Dakota, if the product is, in our judgment, defective. All materials must be accompanied by an RMA (Returned Material Authorization) number requested by and authorized in advance of returning the materials. Shur-Co.® shall not be liable or responsible to supply or pay labor to replace any part found defective, nor shall it be liable for any damages of any kind or nature to person, product, or property. There are no warranties for used products or products that have been repaired, altered, modified, subjected to misuse, negligence, accident or ordinary wear and tear. Shur-Co.® products are sold without any express warranty except as set forth above. Shur-Co.® is not obligated to honor warranty claims if Genuine Shur-Co.® parts are not utilized.

TruXedo TruxSeal Tailgate Seal Installation

READ INSTRUCTIONS CAREFULLLY PRIOR TO INSTALLATION
The following instructions are valid for all makes and models of pickups, foreign and domestic. Due to the variety of designs, however, the Applications of TruxSeal™ to your vehicle may differ slightly. The best way to evaluate which method is best for your vehicle is to cut 1" piece of TruxSeal™ and attach the seal to ensure that the bulb compresses when the tailgate is closed. Experiment with the 1" piece until you find the best configuration for your vehicle.

PLEASE NOTE: TruxSeal™ will always apply bulb side up to the horizontal area of the bed.

ITEMS NEEDED TO PROPERLY INSTALL TruxSeal™:
1. Scissors or utility knife
2. Clean rags
3. Warm water and mild dishwashing soap solution

STEP 1: Clean area thoroughly with soap and water solution where TruxSeal™ is to be applied. Wipe the area until it is completely dry. Use alcohol pads included to further prepare the Applications area. Allow the area to dry for a couple of minutes.

STEP 2: Ensure that tailgate is down prior to Applications. Measure the length of the area from sidewall to sidewall along the bottom of the bed of your pick-up. Cut a piece of TruxSeal™ to the length that is necessary to cover the area. Peel back orange liner and apply TruxSeal™ in a straight line to the bottom edge of the bed first. Begin at one sidewall and continue to the opposing sidewall. The flat portion on the top of the bulb should be flush with the flat portion of the bed. Apply pressure to the seal by running your finger across the entire length. Close the tailgate to confirm that the bulb is compressing when closed.

STEP 3: Cut a small piece of TruxSeal™ (to be adhered to the side wall of the bed) to the length that will provide a seal up to the top of the tailgate. Begin at the bottom and continue as in Step 2. Apply TruxSeal™ to both sides in identical fashion. Be sure to close the tailgate to evaluate the compression of the seal. Small adjustments may need to be made to properly affix the seal.

STEP 4: Completely close the tailgate. If you see any daylight between the seal and the tailgate, you can make a small adjustment by slightly removing the seal and replacing it where it makes a better seal.

TruXedo TruxSeal Tailgate Seal Feature Images

	Designed for Tailgates: Adhesive-backed Acrylic Foam, installs with 3M adhesive. Universal tailgate sealing kit for all makes and models of trucks
	Install Diagram: Clean area, the just cut, peel and stick. Its that easy