TruXedo Lo Pro QT Tonneau Cover
- Low Profile Appearance
- Vehicle Specific Design
- Quick Release Header
- Spring Loaded Tension Control
- Superior Velcro Fastening
- Fast & Easy Rollup Design
- 4 Way Sealing System
- Automatic Rear Latching
- Made in the USA - Yankton, SD
You purchased your truck to look good but also get some work done and your truck bed cover should do same. The TruXedo Lo Pro QT tonneau cover does exactly that! It is easy to use, has a sleek low profile appearance and constructed from heavy duty materials which makes this cover a must have.
This TruXedo tonneau cover has sorts of features and is constructed with a heavy duty black anodized aluminum frame. A highly durable double coated vinyl is strong enough to handle even the harshest of climates. It can withstand the wind and cold of the brutal North Dakota winters and the extreme heat of the Arizona summers with no lasting effects. The patented automatic tension control system ensures the cover remains tight no matter what conditions. TruXedo also features side and corner sealing preventing water, dust and dirt from getting in your truck bed.
The TruXedo Lo Pro QT tonneau cover mounts inside the truck bed rails allowing you to add other great items like stake pocket tie downs and chrome bed rails. A slanted rail design with 1 ½" wide Velcro strips allows a super low profile appearance and holds the cover down better than stretching it over the rail. The Velcro strip is free floating in the track allowing for expanding and contracting in extreme weather. Your items are still safe and sound inside your bed with an ingenious rear latching system that locks into place and can only be opened after opening your tailgate.
Add a TruXedo Lo Pro QT tonneau cover and get your truck dressed up for the party, then roll it up when it's time for work!
|TruXedo Lo Pro QT Features|
|TruXedo Tonneau Cover Comparison|
The cargo management, utili-track, or deck rail system options refer to the factory installed rail system designed to hold moveable cargo cleats along the inside of your truck bed. Please call us for further clarification.
Frequently Asked Questions
What is needed for maintenance?
The vinyl can be cleaned with mild soap and water as well as in a car wash. Make sure to rinse soap of thoroughly. Don't use citrus based or petroleum products as well as silicone based products.
Is the TruXedo Lo Pro Weather proof?
No Tonno is completely weather proof, but the TruXedo Lo Pro QT was designed to keep rain, snow and sleet out of your truck bed. Not to mention dust and other debris.
Am I able to use it with a toolbox?
No, this cover uses the entire truck bed area.
What's mounting consisted of?
It mounts to the top of your bed and uses three heavy duty clamps for secure placement.
What other accessories will this cover work with?
It can be used with bed liners and bed caps.
Can I lock?
It cannot be opened with your tailgate closed, so make sure to lock your tailgate.
What about fading?
This fabric is very high quality and UV resistant, giving you a flawless and fade resistant finish.
How difficult are they to manage in cold weather?
The fabric expands slightly in the cold, but very easy to operate, even at 20 below.
The TruXedo Lo Pro QT Tonneau Cover by TruXedo Tonneau Covers offers an easy at home no drill installation. For additional information see the install manual below or call us at 1-877-216-5446.
Related Articles (9)
Product Reviews Summary
|Ease of Installation||4.7|
|Price / Value||4.6|
|219 Customer Reviews|
|I bought a Lo Pro QT for my new 2014 F-150. I noticed that one review stated that 2 teenagers installed the Lo Pro in 30 minutes. I installed mine in 40 minutes by myself, and I'm not mechanically inclined. Simple installation, 3 side rail clamps for each side. The front rail snaps in place, roll out the cover, and the back bar snaps in place and locks. That's it. The preset tension adjustment was exactly right...I have yet to need to re-adjust it. I was surprised at the simplicity and exact fit. The rear latch works smooth as silk. Both sides unlock with a single lever on the left side, and locks back in place by pressing down on the rear bar. Looks great, well designed. When I trade trucks, I'll be buying a TruXedo Lo Pro again.|
|I hate these covers in general. That being said I love this cover so much! its easy open close and no need to stretch. strong but manageable velcro! im going to put e-track and cut down a load bar to protect the cab side when its open and I need to strap down something to the cab side of bed. this thing has been opened and close over 100 times and works same as day i got it if not better!|
|This was fairly easy to install, once I had finished the task. If I had to do it again it probably would only take me 15 minutes at the most. I HAVE ONLY HAD IT ON THE TRUCK FOR 2 months but I think I made the right purchasing this product.|
|Easy to install. A little expensive but very sturdy and has handled pretty large snowfalls.|
|Looks great; works great. Instructions could have been a little more detailed, but they were adequate. Installation is tricky with only one set of hands, but I was able to do it in about 40 minutes with a couple pressure clamps to hold the mounting rails in place. The Ford F150 cap covers are only on 3 sides, not the bed wall by the cab. So lining it up to be flush was a bit tricky and the weather stripping leaves a slight gap there. However, I have driven it through some fairly heavy ran and no water got in the bed despite the small gaps. Wish I could close the tailgate without releasing the cover, but I knew that going in and once I got used to it, it wasn't inconvenient anymore.|
|I replaced a well-used cover of the "value" version of this add-on on my 2007 Toyota Tundra. The prior cover ended up with a broken latch and degradation of vinyl edges and velcro after 7 years. New cover was extremely easy to install and the low profile is sweet looking. The one-latch release is definitely my favorite. The spring adjustments worked well too. What I didnt' like was the way to get that low profile look -- was to move the frame of the cover to the inside of the bed rails. These stick into the bed of the truck about 3 inches on each side. Versus the prior version sat on top of the bed rail.I am a little concerned over laying things against the side of the bed which would be leaning/touching this cover frame (and thin metal at that). Overall I would recommend this cover for the low-profile look, a little concerned over the cover frame extending into top of bed and potential damage to it with use -- as this is a high-use truck for hauling horses, hay and all the equipment.|
|Had the Low Pro QT for just short of 2 months. I have been on the Interstate for a total of 40 hours of driving in several rain showers and have found this tonneau to be superior to another high rated tonneau. Very little leakage from rain, and once adjusted there is very little buffeting from wind! It is easy to install and very easy to adjust once installed. Latching mechanism is far superior to my previous Extang Revolution, which was a good tonneau! Time will tell how well it holds up with continued use! Will try to update this review in a year.|
|First, kudos to RealTruck for awesome customer service and lightning fast delivery (free!). Installation definitely made easier with the Tacoma-specific instructions, but they're a little vague on the placement of the supplemental weather strips. Other than that, installed easily (less than an hour by myself). Like that it integrates with the Tacoma cargo management rails, including the tie-downs. Granted, the placement options for the tie-downs will be limited by the rail brackets, but that's an acceptable trade-off. Definitely a no-brainer to use, and looks GREAT. Will need some fine-tuning, as I took on a little water in the bulkhead area after the first rain (from the corners). That might be an easy fix with some auto/boat weather stripping from the local hardware store; will also need to bring the side rails down about 1/8 inch so the rubber flap on the back makes contact with the tailgate. Again, very minor adjustments that are probably required on most installations.|
All in all, a very good product that adds a lot of functionality -- and good looks -- to the Tacoma.
|Great product third one I've had (third truck). Installed it in the dark it was so easy. Looks great with the low profile.|